AN ESTIMATION METHOD OF BEARING STRENGTH OF BOLTED JOINTS IN FIBRE REINFORCED COMPOSITE

摘要/Abstract

摘要： Some researchers have estimated the strength of bolted joints in fibre reinforced composite, using simple and efficient engineering procedures. However, for these procedures the effect of clamping due to the strength of bolted joints is not considered. In this paper, a method is presented for predicating critical bearing strength of single-hole bolted joints in composite on the basis of observing and analysing the results of experiments. The clamping effect of bolts is considered. The calculated results correspond to the test data on Glaphic/Epoxy laminates.

关键词: shaft, hysteretic-type internal friction of material, Hopf bifurcation, non-synchronous whirl

Abstract: Some researchers have estimated the strength of bolted joints in fibre reinforced composite, using simple and efficient engineering procedures. However, for these procedures the effect of clamping due to the strength of bolted joints is not considered. In this paper, a method is presented for predicating critical bearing strength of single-hole bolted joints in composite on the basis of observing and analysing the results of experiments. The clamping effect of bolts is considered. The calculated results correspond to the test data on Glaphic/Epoxy laminates.

Key words: shaft, hysteretic-type internal friction of material, Hopf bifurcation, non-synchronous whirl

羊妗. AN ESTIMATION METHOD OF BEARING STRENGTH OF BOLTED JOINTS IN FIBRE REINFORCED COMPOSITE[J]. Applied Mathematics and Mechanics (English Edition), 1986, 7(1): 103-109.

Yang Ling. AN ESTIMATION METHOD OF BEARING STRENGTH OF BOLTED JOINTS IN FIBRE REINFORCED COMPOSITE[J]. Applied Mathematics and Mechanics (English Edition), 1986, 7(1): 103-109.

参考文献

[1] Yang,L.Bolted joint design of composite,N.P.U.Technical Report,SHJ 8217(1980. 12).
[2] Waszezak,J.P.and T.A.Cruse.Failure mode and strength prediction of anisotropic bolt bearing specimens,J of Composite Materials,5(1971),421.
[3] Jong,Theo.De., Stresses around pin-loaded holes in elastically orthotropic or isotropic plates,J.Composite Materials.2(1977),313.
[4] Eisenmann,J.R.,Bolted joint static strength model for composite materials,NASA-TM-X-3377(1976).
[5] Hart-Smith,L.J.,Bolted joints in graphite epoxy composites.Douglas Aircraft Company,NASA Contract Report,No NASA CR-144899(1976).
[6] Collings,T.A.,The strength of bolted joints in multidirectional CFRP laminates,Composites.8(1977).
[7] Quinn,W.J and F.L.Matthews,The effect of stacking Sequence on the pin-bearing strength in glass fibre reinforced plastic,J Cmposite Materials.2(1977),139.
[8] Kim,R.Y and J.M.Whitney,Effect of temperature and moisture on pin bearing strength of composite laminates,J Composite Materials.10(1976),149.
[9] Wilson.D.W and R B.Pipes.Analysis of the shearout failure mode in composite bolted joints,Composite Structure.p 34.
[10] Tang,S.,Failare of composite joint under combined tension and bolt loads.J Composite Materials.15(1981),329.
[11] Soui,S.R.,Failure analysis of composite laminates with a fastener hole.Joining of Composite Material.p.145.
[12] Soni.S.R.,Stress and strength analysis of bolted joints in composite laminates,Composite structure,p.50.
[13] Wu.J Q.,Strength test and study of stress concentration factor for bolted joint in Graphite/Epoxy composite laminates,Technical Report,ministry of Aeronautical industry.
[14] Chen.S.J.,Test report in composite joints Technical Report.Ministry of Aeronautical industry.
[15] Yang,B.Z.,Expental study of bearing strength for Graphite/Epoxy composite laminates,N.P.U Technical Report.SHJ 8289(1982 11).
[16] Yang,L,Stresses analysis around a hole in CFRP laminated plates.N.P.U Technical Report,SHJ 8217.